61826-2RS Deep Groove Ball Bearing (130x165x18mm)

How to read this designation →

d — BoreD — Outside DiameterB — Width

Bearing dimensions and basic technical information.

Schematic of a contact-sealed (2RS) single-row deep groove ball bearing with rubber seals

Schematic only — for the actual construction, refer to each manufacturer's information.

Bore diameter (d)130 mm

Outer diameter (D)165 mm

Width (B)18 mm

TypeDeep Groove Ball Bearing

RowSingle Row

ClearanceCN

Cage

Material Steel

Cage materials — Deep Groove Ball Bearing

Suffix	Material	Printed by
`(none)`	Pressed steel	NSK, NTN, Timken
`M / MA / MB`	Machined brass	SKF, Schaeffler (FAG), Timken
`TN9 / TVP / TVH`	Polyamide (glass-fibre reinforced PA66)	SKF, Schaeffler (FAG)
`PH`	PEEK	SKF

Suffix letters are set by each manufacturer; the third column names the brands that print the row. Always confirm the exact variant in the manufacturer's table.

Clearance groups

Group	Meaning
`C2`	Radial internal clearance smaller than normal
`CN`	Normal clearance — the ISO default group, usually not printed in the designation (SKF/FAG may write it as CN or C0)
`C3`	Radial internal clearance greater than normal
`C4`	Greater than C3

CN is the ISO normal clearance group and is usually not printed in the designation; other groups include C2, C3 and C4. The numeric ranges are defined per bearing type and size (ISO 5753), so always compare them in the manufacturer's table.

Bearing materials

Material	Where it appears
Bearing steel	Rings and rolling elements — the standard for every model without a special material note
Stainless steel	Corrosion-resistant versions, e.g. the SKF "W" series
Ceramic rolling elements (hybrid)	Ceramic balls or rollers running in steel rings; electrically insulating and tolerant of poor lubrication
Ceramic-coated steel rings	SKF INSOCOAT: VL0241 coats the outer ring, VL2071 the inner ring (electrical insulation against stray currents)

The material refers to the rings and the rolling elements. Unless a special material is stated, both are bearing steel.

Base model: 61826

Related designations: SKF 61826-2RS1 · NSK 6826DDU · NTN 6826LLU · Timken 61826-2RS

Suffix Information

Suffix Code2RS

CategorySeal

MeaningContact seals on both sides

DescriptionRubber contact seals on both sides of the bearing.

Manufacturer Ratings

Load-rating symbols are printed as each manufacturer writes them in its own catalogue, so the same quantity can carry a different symbol from brand to brand.

Brand	Dynamic Load Rating	Static Load Rating	Fatigue Load Limit
SKF 61826-2RS1	C37.7 kN	C043 kN	Pu1.6 kN
NSK 6826DDU	Cr40.5 kN	C0r44 kN	—
NTN 6826LLU	Cr41 kN	C0r41 kN	Cu2.25 kN
Timken 61826-2RS	Cr37.9 kN	C0r42.9 kN	—

Speed Ratings

Speed limits depend on sealing and lubrication, and definitions differ by manufacturer. The figures below are for this sealed version (61826-2RS). Contact seals are greased for life and run slower than the open bearing. Always confirm the exact variant in the manufacturer's table.

Brand	Grease sealed (2RS)	Oil sealed (2RS)	Reference	Limiting
SKF 61826-2RS1	—	—	—	2,200 r/min
NSK 6826DDU	2,000 r/min	—	—	—
NTN 6826LLU	2,000 r/min	—	—	—
Timken 61826-2RS	—	—	—	—

Timken does not publish a limiting speed for this sealed variant.

References

SKF — SKF Group, Rolling Bearings, PUB BU/P1 17000/1 EN, Oct. 2018.
NSK — NSK Ltd., Rolling Bearings for Industrial Machinery, CAT. No. E1103, Tokyo, Japan, Jan. 2025.
NTN — NTN Corporation, Ball and Roller Bearings, CAT. No. 2203-3E, Osaka, Japan, Sep. 2000.
Timken — The Timken Company, Deep Groove Ball Bearings, Catalog 10857, North Canton, OH, USA.

Related Guides

Disclaimer: Data on this page is compiled from publicly available online sources for reference only, and not every model appears in a manufacturer's published catalog. Values may differ between sources and editions — always verify against the manufacturer's current documentation before design or purchase.Full disclaimer →