16020 Deep Groove Ball Bearing (100x150x16mm)

How to read this designation →

d — BoreD — Outside DiameterB — Width

Bearing dimensions and basic technical information.

Schematic of an open single-row deep groove ball bearing with a pressed steel cage

Schematic only — for the actual construction, refer to each manufacturer's information.

Bore diameter (d)100 mm

Outer diameter (D)150 mm

Width (B)16 mm

TypeDeep Groove Ball Bearing

RowSingle Row

ClearanceCN

Cage

Material Steel

Cage materials — Deep Groove Ball Bearing

Suffix	Material	Printed by
`(none)`	Pressed steel	NSK, NTN, Timken
`M / MA / MB`	Machined brass	SKF, Schaeffler (FAG), Timken
`TN9 / TVP / TVH`	Polyamide (glass-fibre reinforced PA66)	SKF, Schaeffler (FAG)
`PH`	PEEK	SKF

Suffix letters are set by each manufacturer; the third column names the brands that print the row. Always confirm the exact variant in the manufacturer's table.

Clearance groups

Group	Meaning
`C2`	Radial internal clearance smaller than normal
`CN`	Normal clearance — the ISO default group, usually not printed in the designation (SKF/FAG may write it as CN or C0)
`C3`	Radial internal clearance greater than normal
`C4`	Greater than C3

CN is the ISO normal clearance group and is usually not printed in the designation; other groups include C2, C3 and C4. The numeric ranges are defined per bearing type and size (ISO 5753), so always compare them in the manufacturer's table.

Bearing materials

Material	Where it appears
Bearing steel	Rings and rolling elements — the standard for every model without a special material note
Stainless steel	Corrosion-resistant versions, e.g. the SKF "W" series
Ceramic rolling elements (hybrid)	Ceramic balls or rollers running in steel rings; electrically insulating and tolerant of poor lubrication
Ceramic-coated steel rings	SKF INSOCOAT: VL0241 coats the outer ring, VL2071 the inner ring (electrical insulation against stray currents)

The material refers to the rings and the rolling elements. Unless a special material is stated, both are bearing steel.

Manufacturer Ratings

Load-rating symbols are printed as each manufacturer writes them in its own catalogue, so the same quantity can carry a different symbol from brand to brand.

Brand	Dynamic Load Rating	Static Load Rating	Fatigue Load Limit
SKF 16020	C46.2 kN	C044 kN	Pu1.7 kN
NSK 16020	Cr46.5 kN	C0r42 kN	—
Schaeffler (FAG) 16020	Cr46.5 kN	C0r44.5 kN	Cur2.21 kN
NTN 16020	Cr39 kN	C0r36.5 kN	Cu2.18 kN
Timken 16020	Cr43.8 kN	C0r44.3 kN	—

Speed Ratings

Speed limits depend on sealing and lubrication, and definitions differ by manufacturer. Contact-sealed variants are normally greased for life and run slower. Always confirm the exact variant in the manufacturer's table.

Brand	Grease open / shielded	Oil open	Reference	Limiting
SKF 16020	—	—	9,500 r/min	5,600 r/min
NSK 16020	4,300 r/min	5,300 r/min	—	—
Schaeffler (FAG) 16020	—	—	4,000 r/min	6,300 r/min
NTN 16020	4,200 r/min	5,000 r/min	—	—
Timken 16020	3,800 r/min	5,400 r/min	—	—

References

SKF — SKF Group, Rolling Bearings, PUB BU/P1 17000/1 EN, Oct. 2018.
NSK — NSK Ltd., Rolling Bearings for Industrial Machinery, CAT. No. E1103, Tokyo, Japan, Jan. 2025.
Schaeffler (FAG) — Schaeffler Technologies AG & Co. KG, Rolling Bearings, HR 1, Herzogenaurach, Germany, Feb. 2025.
NTN — NTN Corporation, Ball and Roller Bearings, CAT. No. 2203-3E, Osaka, Japan, Sep. 2000.
Timken — The Timken Company, Deep Groove Ball Bearings, Catalog 10857, North Canton, OH, USA.

Related Guides

Disclaimer: Data on this page is compiled from publicly available online sources for reference only, and not every model appears in a manufacturer's published catalog. Values may differ between sources and editions — always verify against the manufacturer's current documentation before design or purchase.Full disclaimer →